1、稱量前應檢查天平是否正常,是否處于水平位置,吊耳、圈碼是否脫落,玻璃框內外是否清潔;
2、接通電源,打開電源開關和天平開關,預熱至少30分鐘以上;電子分析天平應從左右兩門取放稱量物和砝碼;
3、將被稱物預先放置與天平的溫度一致(過冷、過熱物品均不能放在天平內稱量),必要時先用臺式天平稱出被稱物大約重量。開啟天平側門,將被稱物置于天平載物盤中央;放入被稱物時應戴手套或用帶橡皮套的鑷子鑷取,不應直接用手接觸。并且必須輕拿輕放;
4、稱量不得超過天平的大載荷,不能超過天平負載200克;有腐蝕性或吸濕性物體必須放在密閉容器中稱量。同一化學試驗中的所有稱量,應自始至終使用同一架天平,使用不同天平會(huì )造成誤差。
5、開啟升降旋鈕(開關旋鈕)時,一定要輕放,以免損傷瑪瑙刀口。每次加減砝碼、圈碼或取放稱量物時,一定要先關升降旋鈕(關閉天平),加完后,再開啟旋鈕(開啟天平);
6、讀數時,一定要將升降旋鈕開關順時針旋轉到底,天平開啟。天平自動顯示被測物質的重量,等穩定后(顯示屏左側亮點消失)即可讀數并記錄;
7、每架天平都配有固定的砝碼,不能錯用其他天平的砝碼。保持砝碼清潔干燥.砝碼只許用鑷子夾取,絕不能用手拿,用完放回砝碼盒內;
8、轉動圈碼讀書時動作要輕而緩慢,以免圈碼調落;電子分析天平內應放置干燥劑,常用變色硅膠,應定期更換;
9、稱量完畢,應檢查電子分析天平天平梁是否托起,砝碼是否已歸位,指數盤是否轉到"0",電源是否切斷,邊門是否關好. 后罩好天平;
10、經常保持天平內部清潔,必要時用軟毛刷或綢布抹凈或用無水乙醇擦凈;應按計量部門規定定期校正,并有專人保管,負責維護保養。