實驗室電子天平基于電磁力平衡原理,全量程無需砝碼即可直接稱重。放置稱重物體后,幾秒鐘內達到平衡并顯示讀數。稱重速度快,準確度高。電子天平的支點采用彈性簧片代替機械天平的瑪瑙刀口,差動變壓器代替升降樞軸設備,數顯代替指針刻度式,具有使用壽命長、功能穩定、操作簡單、靈敏度高等特點。此外,它還具有主動校正、主動剝離、過載指示、故障報警和質量電信號輸出等功能,是定量分析中的重要儀器。充分了解儀器的性能,掌握儀器的使用方法,是分析結果可靠的保證。
實驗室電子天平操作方法:
1、水平調節。觀察電平表。如果液位計的氣泡偏移,調整水平調節腳,使氣泡位于液位計的中間。
2、預熱。打開電源,預熱到預定時間,然后打開顯示屏進行操作。
3、打開顯示屏。輕輕按開鍵,顯示屏將全亮。約2S后,顯示天平類型,稱量表為0.0000g。
4、平衡基本形式的選擇。天平通常以“正常狀態”的形式出現,并具有停電召回功能。如果在申請過程中更改為其他形式,申請后一旦按下關閉鍵,余額將恢復為通常的形式。
5、校準。天平安裝后,使用前應進行天平校準。由于存放時間長、方位移動、環境變化或測量不準確等原因,天平在使用前通常應進行校準。本天平采用外標定(部分電子天平具有內標定功能),通過焦油鍵清除、Cal減法和100g標定砝碼完成。
6、稱量。按tar鍵,實驗室電子天平顯示為零后,將被稱物放在秤盤上,待數字穩定后,即顯示屏左下角的“0”符號缺失,質量值為可以讀出稱重的物體。
7、剝皮稱重。按tar鍵清零,將容器放在秤盤上,天平顯示容器質量,再按tar鍵顯示清零,即去掉皮重。將被稱重的物體重新放入容器中,或將被稱重的物體(粉末或液體)逐漸加入容器中,直至達到所需的質量。當可視化器左下角的“0”缺失時,出現稱重物體的凈質量。拿走秤上的所有物品后,天平顯示負值。按tar鍵,天平顯示0.0000g。如果秤盤上的總質量超過最大負載(fa1604電子天平為160g),天平只顯示上段,此時應立即減少負載。
8、稱重后,如果短時間內還在使用天平(或其他人也在使用天平),通常不需要按關機鍵關閉顯示。測試完成后,關閉顯示器并切斷電源。如果天平在短時間內使用(如2H),則無需切斷電源,可節省預熱時間。
實驗室電子天平使用注意事項:
1、天平應放置在堅固穩固的水泥平臺或木質平臺上。房間應清潔、干燥并保持相對恒定的溫度。同時,應避免光線直射天平。
2、稱量時,從側門取放物質,讀數時關閉箱門,以免氣流引起天平擺動。前門僅用于維護或清除殘留物質。
3、電子精密天平若長期不使用,應定期開機預熱,每周一次,每次2h,以確保儀器始終處于良好狀態。
4、天平箱內應放置吸濕劑(如硅膠)。吸濕劑吸水后變色時,應立即高溫烘烤更換,以保證吸濕。
5、揮發性、腐蝕性、強酸、強堿物質應在有蓋的稱量瓶中稱量,以防止天平腐蝕。